[SMART] Stan dysku

Wszystko o naszych urządzeniach: PC, laptopy, jednopłytkowce, itp - problemy ze sprzętem , aplikacjami itd.
Awatar użytkownika
inż.wielki
User
User
Posty: 307
Rejestracja: niedziela 20 gru 2015, 23:11

[SMART] Stan dysku

Postautor: inż.wielki » poniedziałek 16 lip 2018, 10:38

Witam,
odczytałem smart dysku. Wydaje mi się że z dyskiem nie jest tragicznie. Ale nie jest też to dysk pierwszej świeżości. Czy ktoś obeznany ze S.M.A.R.T może podzielić się swoimi wnioskami na ten temat? Przyznam że nie za dobrze umiem czytać te parametry ;)


Kod: Zaznacz cały

smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.13.0-45-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Momentus 5400.6
Device Model:     ST9320325AS
Serial Number:    6VE329TY
LU WWN Device Id: 5 000c50 01b5646a0
Firmware Version: 0002SDM1
User Capacity:    320,072,933,376 bytes [320 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    5400 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 2.6, 3.0 Gb/s
Local Time is:    Mon Jul 16 09:54:36 2018 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (    0) seconds.
Offline data collection
capabilities:                    (0x73) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        No Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   1) minutes.
Extended self-test routine
recommended polling time:        ( 109) minutes.
Conveyance self-test routine
recommended polling time:        (   2) minutes.
SCT capabilities:              (0x103b) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   114   085   006    Pre-fail  Always       -       74823919
  3 Spin_Up_Time            0x0003   099   098   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   083   083   020    Old_age   Always       -       17711
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   082   060   030    Pre-fail  Always       -       184672917
  9 Power_On_Hours          0x0032   089   089   000    Old_age   Always       -       10247
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   091   037   020    Old_age   Always       -       9871
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   001   001   000    Old_age   Always       -       4530
188 Command_Timeout         0x0032   100   100   000    Old_age   Always       -       4
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   070   047   045    Old_age   Always       -       30 (Min/Max 28/30)
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       1003
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       83
193 Load_Cycle_Count        0x0032   019   019   000    Old_age   Always       -       163819
194 Temperature_Celsius     0x0022   030   053   000    Old_age   Always       -       30 (0 17 0 0 0)
195 Hardware_ECC_Recovered  0x001a   069   057   000    Old_age   Always       -       74823919
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       1
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       1
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
254 Free_Fall_Sensor        0x0032   100   100   000    Old_age   Always       -       0

SMART Error Log Version: 1
ATA Error Count: 5547 (device log contains only the most recent five errors)
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 5547 occurred at disk power-on lifetime: 10242 hours (426 days + 18 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 1c 84 e0 01  Error: UNC at LBA = 0x01e0841c = 31491100

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 00 08 84 e0 41 00      00:43:23.792  READ FPDMA QUEUED
  2f 00 01 10 00 00 40 00      00:43:23.685  READ LOG EXT
  60 00 00 08 84 e0 41 00      00:43:21.415  READ FPDMA QUEUED
  2f 00 01 10 00 00 40 00      00:43:21.353  READ LOG EXT
  61 00 08 48 a5 30 42 00      00:43:19.092  WRITE FPDMA QUEUED

Error 5546 occurred at disk power-on lifetime: 10242 hours (426 days + 18 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 1c 84 e0 01  Error: UNC at LBA = 0x01e0841c = 31491100

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 00 08 84 e0 41 00      00:43:21.415  READ FPDMA QUEUED
  2f 00 01 10 00 00 40 00      00:43:21.353  READ LOG EXT
  61 00 08 48 a5 30 42 00      00:43:19.092  WRITE FPDMA QUEUED
  60 00 00 08 84 e0 41 00      00:43:19.091  READ FPDMA QUEUED
  2f 00 01 10 00 00 40 00      00:43:18.954  READ LOG EXT

Error 5545 occurred at disk power-on lifetime: 10242 hours (426 days + 18 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 1c 84 e0 01  Error: WP at LBA = 0x01e0841c = 31491100

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  61 00 08 48 a5 30 42 00      00:43:19.092  WRITE FPDMA QUEUED
  60 00 00 08 84 e0 41 00      00:43:19.091  READ FPDMA QUEUED
  2f 00 01 10 00 00 40 00      00:43:18.954  READ LOG EXT
  61 00 08 d8 a5 30 42 00      00:43:16.574  WRITE FPDMA QUEUED
  60 00 00 08 84 e0 41 00      00:43:16.574  READ FPDMA QUEUED

Error 5544 occurred at disk power-on lifetime: 10242 hours (426 days + 18 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 1c 84 e0 01  Error: WP at LBA = 0x01e0841c = 31491100

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  61 00 08 d8 a5 30 42 00      00:43:16.574  WRITE FPDMA QUEUED
  60 00 00 08 84 e0 41 00      00:43:16.574  READ FPDMA QUEUED
  61 00 50 d0 ba 31 42 00      00:43:16.574  WRITE FPDMA QUEUED
  60 00 00 08 85 e0 41 00      00:43:16.572  READ FPDMA QUEUED
  2f 00 01 10 00 00 40 00      00:43:16.455  READ LOG EXT

Error 5543 occurred at disk power-on lifetime: 10242 hours (426 days + 18 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 1c 84 e0 01  Error: UNC at LBA = 0x01e0841c = 31491100

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 00 08 85 e0 41 00      00:43:14.088  READ FPDMA QUEUED
  60 00 00 08 84 e0 41 00      00:43:14.087  READ FPDMA QUEUED
  61 00 50 d0 ba 31 42 00      00:43:14.087  WRITE FPDMA QUEUED
  60 00 00 08 83 e0 41 00      00:43:14.087  READ FPDMA QUEUED
  60 00 00 08 82 e0 41 00      00:43:14.086  READ FPDMA QUEUED

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Awatar użytkownika
ZbeeGin
User
User
Posty: 492
Rejestracja: sobota 08 lip 2017, 17:16
Lokalizacja: Śląsko-Zagłębiowska Metropolia
Kontaktowanie:

Re: [SMART] Stan dysku

Postautor: ZbeeGin » poniedziałek 16 lip 2018, 11:31

10tyś godzin. Brak sektorów relokowanych. Jeden niestabilny. Powierzchnia jeszcze niczego sobie.
Filmy czy muzykę jeszcze mógłbyś na nim trzymać. Do innych zadań by się raczej nie nadał z racji wieku i parametrów (tylko 5400rpm i 8MB bufora).

Awatar użytkownika
inż.wielki
User
User
Posty: 307
Rejestracja: niedziela 20 gru 2015, 23:11

Re: [SMART] Stan dysku

Postautor: inż.wielki » poniedziałek 16 lip 2018, 12:38

Tak też myślałem. Dzięki za potwierdzenie


Wróć do „Sprzęt, sterowniki, oprogramowanie”

Kto jest online

Użytkownicy przeglądający to forum: Obecnie na forum nie ma żadnego zarejestrowanego użytkownika i 4 gości