odczytałem smart dysku. Wydaje mi się że z dyskiem nie jest tragicznie. Ale nie jest też to dysk pierwszej świeżości. Czy ktoś obeznany ze S.M.A.R.T może podzielić się swoimi wnioskami na ten temat? Przyznam że nie za dobrze umiem czytać te parametry
Kod: Zaznacz cały
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.13.0-45-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Momentus 5400.6
Device Model: ST9320325AS
Serial Number: 6VE329TY
LU WWN Device Id: 5 000c50 01b5646a0
Firmware Version: 0002SDM1
User Capacity: 320,072,933,376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Mon Jul 16 09:54:36 2018 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 109) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103b) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 114 085 006 Pre-fail Always - 74823919
3 Spin_Up_Time 0x0003 099 098 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 083 083 020 Old_age Always - 17711
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 082 060 030 Pre-fail Always - 184672917
9 Power_On_Hours 0x0032 089 089 000 Old_age Always - 10247
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 091 037 020 Old_age Always - 9871
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 4530
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 4
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 070 047 045 Old_age Always - 30 (Min/Max 28/30)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 1003
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 83
193 Load_Cycle_Count 0x0032 019 019 000 Old_age Always - 163819
194 Temperature_Celsius 0x0022 030 053 000 Old_age Always - 30 (0 17 0 0 0)
195 Hardware_ECC_Recovered 0x001a 069 057 000 Old_age Always - 74823919
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 1
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 1
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 5547 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 5547 occurred at disk power-on lifetime: 10242 hours (426 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 1c 84 e0 01 Error: UNC at LBA = 0x01e0841c = 31491100
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 08 84 e0 41 00 00:43:23.792 READ FPDMA QUEUED
2f 00 01 10 00 00 40 00 00:43:23.685 READ LOG EXT
60 00 00 08 84 e0 41 00 00:43:21.415 READ FPDMA QUEUED
2f 00 01 10 00 00 40 00 00:43:21.353 READ LOG EXT
61 00 08 48 a5 30 42 00 00:43:19.092 WRITE FPDMA QUEUED
Error 5546 occurred at disk power-on lifetime: 10242 hours (426 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 1c 84 e0 01 Error: UNC at LBA = 0x01e0841c = 31491100
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 08 84 e0 41 00 00:43:21.415 READ FPDMA QUEUED
2f 00 01 10 00 00 40 00 00:43:21.353 READ LOG EXT
61 00 08 48 a5 30 42 00 00:43:19.092 WRITE FPDMA QUEUED
60 00 00 08 84 e0 41 00 00:43:19.091 READ FPDMA QUEUED
2f 00 01 10 00 00 40 00 00:43:18.954 READ LOG EXT
Error 5545 occurred at disk power-on lifetime: 10242 hours (426 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 1c 84 e0 01 Error: WP at LBA = 0x01e0841c = 31491100
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 00 08 48 a5 30 42 00 00:43:19.092 WRITE FPDMA QUEUED
60 00 00 08 84 e0 41 00 00:43:19.091 READ FPDMA QUEUED
2f 00 01 10 00 00 40 00 00:43:18.954 READ LOG EXT
61 00 08 d8 a5 30 42 00 00:43:16.574 WRITE FPDMA QUEUED
60 00 00 08 84 e0 41 00 00:43:16.574 READ FPDMA QUEUED
Error 5544 occurred at disk power-on lifetime: 10242 hours (426 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 1c 84 e0 01 Error: WP at LBA = 0x01e0841c = 31491100
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 00 08 d8 a5 30 42 00 00:43:16.574 WRITE FPDMA QUEUED
60 00 00 08 84 e0 41 00 00:43:16.574 READ FPDMA QUEUED
61 00 50 d0 ba 31 42 00 00:43:16.574 WRITE FPDMA QUEUED
60 00 00 08 85 e0 41 00 00:43:16.572 READ FPDMA QUEUED
2f 00 01 10 00 00 40 00 00:43:16.455 READ LOG EXT
Error 5543 occurred at disk power-on lifetime: 10242 hours (426 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 1c 84 e0 01 Error: UNC at LBA = 0x01e0841c = 31491100
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 08 85 e0 41 00 00:43:14.088 READ FPDMA QUEUED
60 00 00 08 84 e0 41 00 00:43:14.087 READ FPDMA QUEUED
61 00 50 d0 ba 31 42 00 00:43:14.087 WRITE FPDMA QUEUED
60 00 00 08 83 e0 41 00 00:43:14.087 READ FPDMA QUEUED
60 00 00 08 82 e0 41 00 00:43:14.086 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.